Register
Results 1 to 2 of 2
  1. #1
    FTA66 MODERATOR chevy85's Avatar
    Join Date
    Mar 2013
    Posts
    746
    Post Thanks / Like

    Cool XTREME 4.14 /5.02 bin for Nfusion SD (no PC running but with EPG)



    UPDATED SEP 2, 2012 - WITH NEW 4.14 RELEASE-various bug issues corrected... (see release notes)-credit goes to site member solofta
    ----------------

    Xtreme Instruction for Nfusion SD Only

    - If you are already using Boris T4 / T54 bin, start on step 1
    - If your receiver was not converted for private server use, start with step 2.
    - If you are already using NOI bin, start with step 5
    - If you are already using Nfusion 58W (or its variants) bin, start with step 7
    - If you are already running on an older Xtreme bin, just load the latest Xtreme bin in the “Main” using the Nfusion loader.


    1. Load the boot_g3x_to r3x_v1.23.bin file in BOOT mode.

    2. Load this file u48 factory file from July 2009 also in BOOT mode.

    3. Load this file next... boot file v.130 also in BOOT mode.

    4. Load this file 090928 sol phoenix sd v153 1 (Maintenance release) in MAIN mode.

    5. Load the file named boot_126.bin.in BOOT mode.

    6. Load the file named nfusion_factory_U17.bin in BOOT mode.

    7. Load the file named XSTV4.14.bin in MAIN mode.

    8. Do a factory default <- very important! Menu > Newcamd Setting > Factory Default

    9. Now Menu TO Newcamd Setting > Server Info>OK> 5585

    Enter your info
    “C” button – clear
    “i” button – cap / small letters / number
    Menu button - previous menu

    When doing url leave second one blank

    Same as password and username and port to leave second one blank.

    When doing DES make sure you do 2 number then a space and so on
    Like this...

    61 03 40 34 45 40 69 70 98 71 23 41 21 34

    After entering info hit menu couple times.

    10. Scan your sats...set time etc.

    11. Confirm that switch port assignments for sats are saved. Sometimes it doesn’t get saved.
    12. Set a valid channel w/good signal
    13. Turn OFF from rear switch and turn ON again <- Very important

    14. Wait for couple of seconds and you’ll get TV


    By XtremeServiceTv


    Notes:
    Normally, power on / off through remote fixes hanging. It might take some seconds before TV shows up after receiver is put off / standby mode. You might need to do channel hopping to get TV. Favorite doesn’t work. Channel lock doesn’t work properly. Only Blind Scan is available for scanning. There are some minor bugs in the software but it works quite well.

    There’s no option for sat 118W (but you can edit tp's on existing sat-for ex 121-see below) but sat 61.5W is available.

    OPTIONAL->ADDING 118 to XTREMETV bin:-credit goes to site member himani364
    ------------------------------------------------------
    step 1
    Menu---installation----set your sat to 121.

    step 2

    put your settings for sat 121 as you should set for 118 (like ports & universal lnb etc)

    now save settings & press menu button, if you accidently exit out go back to menu---installation--- this time you will select channel scan

    step 3

    select 121

    go to TP's section in bottom box

    & start deleting all tp's by pressing "c" button & just leave 1 tp from list in there

    step 4

    go tp Add Tp from top section & start adding Tp's manually

    here is the list:

    118° TP 01 118.0W 11715 V 20000 3/4 FEC QPSK DVB-S
    118° TP 02 118.0W 11728 H 20000 3/4 FEC QPSK DVB-S
    118° TP 03 118.0W 11745 V 20000 3/4 FEC QPSK DVB-S
    118° TP 04 118.0W 11758 H 20000 3/4 FEC QPSK DVB-S
    118° TP 05 118.0W 11776 V 20000 3/4 FEC QPSK DVB-S
    118° TP 06 118.0W 11789 H 20000 3/4 FEC QPSK DVB-S
    118° TP 07 118.0W 11806 V 20000 3/4 FEC QPSK DVB-S
    118° TP 08 118.0W 11819 H 20000 3/4 FEC QPSK DVB-S
    118° TP 09 118.0W 11837 V 20000 3/4 FEC QPSK DVB-S
    118° TP 10 118.0W 11850 H 20000 3/4 FEC QPSK DVB-S
    118° TP 11 118.0W 11867 V 20000 3/4 FEC QPSK DVB-S
    118° TP 12 118.0W 11880 H 20000 3/4 FEC QPSK DVB-S
    118° TP 13 118.0W 11898 V 20000 3/4 FEC QPSK DVB-S
    118° TP 14 118.0W 11911 H 20000 3/4 FEC QPSK DVB-S
    118° TP 15 118.0W 11928 V 20000 3/4 FEC QPSK DVB-S
    118° TP 16 118.0W 11941 H 20000 3/4 FEC QPSK DVB-S
    118° TP 17 118.0W 11959 V 20000 3/4 FEC QPSK DVB-S
    118° TP 18 118.0W 11972 H 20000 3/4 FEC QPSK DVB-S
    118° TP 19 118.0W 11989 V 20000 3/4 FEC QPSK DVB-S
    118° TP 20 118.0W 12002 H 20000 3/4 FEC QPSK DVB-S
    118° TP 21 118.0W 12020 V 20000 3/4 FEC QPSK DVB-S
    118° TP 22 118.0W 12033 H 20000 3/4 FEC QPSK DVB-S
    118° TP 23 118.0W 12050 V 20000 3/4 FEC QPSK DVB-S
    118° TP 24 118.0W 12063 H 20000 3/4 FEC QPSK DVB-S
    118° TP 25 118.0W 12081 V 20000 3/4 FEC QPSK DVB-S
    118° TP 26 118.0W 12094 H 20000 3/4 FEC QPSK DVB-S
    118° TP 27 118.0W 12111 V 20000 3/4 FEC QPSK DVB-S
    118° TP 28 118.0W 12124 H 20000 3/4 FEC QPSK DVB-S
    118° TP 29 118.0W 12142 V 20000 3/4 FEC QPSK DVB-S
    118° TP 30 118.0W 12155 H 20000 3/4 FEC QPSK DVB-S
    118° TP 31 118.0W 12172 V 20000 3/4 FEC QPSK DVB-S
    118° TP 32 118.0W 12185 H 20000 3/4 FEC QPSK DVB-S


    it's little time consuming & channel names are also messed up. However, channel numbers are correct, but in the End it's worth few minutes of work.
    use at your own risk!!!!!
    Attached Files Attached Files

  2. #2
    Super Moderator thunderstruck's Avatar
    Join Date
    Feb 2013
    Posts
    1,431
    Post Thanks / Like
    newer release 5.02

    -load over the extreme file 4.14
    -the server password is 5585





    This 'extreme' software is something I do not endorse. But for testing purposes, here is the new release as requested.

    USE at OWN RISK
    Attached Files Attached Files
    Last edited by thunderstruck; 05-05-2013 at 08:10 PM.

 

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •