STEP by STEP INSTRUCTION TO ADD A NEW SATELLITE
TO YOUR NEOSAT IPRO 2000 USING ANIK F3 118.8W AS AN EXAMPLE



TO ADD A NEW SATELLITE

1. Menu>Installation>Antenna Setup>OK

2. With any satellite highlighted at the top hit the ok button and you will see a list of satellites on the right. Scroll through that list until you see Satellites that are named "Newsat1 to Newsat10 at 0.0W

3. Highlight anyone of the "Newsat#" and hit the green button on your remote to edit that Satellite.

4. You will now see the edit satellite box and

Name Newsat#
Longitude 0.0w
Rename Satellite

With Longitude highlighted use your numbers on your remote and punch in 1188 Which will read out as 118.8W

Next use the arrow down to go to the next line which says Rename Satellite hit the ok button

Now you have on the left hand side a keyboard which you can use with your remote.With the clear button highlighted on the right click ok on your remote and that removes the newsat# from the top display

Now using your arrows on the remote navigate to the A and hit OK on your remote, next scroll to the N and then hit OK on the remote and continue doing so until you have in the top display box ANIK F3.

Now with the OK IN THE DISPLAY HIGHLIGHTED Hit the OK on the remote and YOU HAVE NOW CREATED A NEW SATELLITE FOR YOUR IPRO2000 CALLED ANIK F3 @ 118.8W HIT THE RED BUTTON TO EXIT AND THAT NEWLY NAMED ANIK F3 @ 118.8W WILL BE HIGHLIGHTED IN THE SATELLITE LIST - HIT OK AND IT WILL NOW SHOW UP IN THE ANTENNA SETUP ON THE LEFT.

ADDING IN THE TRANSPONDERS FOR ANIK F3 118.8W

In Antenna Setup with Satellite ANIK F3 118.8W at the top scroll down to the TRANSPONDER and hit OK on your remote and you will see a list on the right called TRANSPONDERS which will have either 1 or no transponders in it.

yOU WILL NOW NEED A LIST OF TRANSPONDERS FOR ANIK F3 WHICH YOU CAN GET HERE:


Anik F3 at 118.8°W - LyngSat

THERE ARE 32 TRANSPONDERS FOR DN LISTED. Once you have your list where you can view it.
.
HIT THE YELLOW KEY ON YOUR REMOTE TO ADD TP AND YOU WILL GET EDIT TRANSPONDER BOX WHICH SHOWS

FREQUENCY NEW

USE YOUR KEYBOARD TO TO ENTER THE NUMERIC VALUE OF THE FREQUENCy of the FIRST TRANSPONDER tp1 such as 11224

SYMBOLRATE NEW

USE YOUR DOWN ARROW TO HIGHLIGHT THE SYMBOLRATE AND TYPE IN THE RATE WHICH IS EITHER 20000 OR 21500 - it is on the lyngsat list in the column that says SR-FEC SID-VPID

POLARIZATION

USE YOUR DOWN ARROW TO HIGHLIGHT POLARIZATION AND USING YOUR L AND R ARROWS YOU WILL SELECT EITHER HOR or VER

SINCE YOUR TRANSPONDER LIST SHOWS L OR R FROM LYNGSAT ENTER THE FOLLOWING:

TRANSPONDERS WITH AN L = HOR
TRANSPONDERS WITH AN R = VER

WHEN YOU COMPLETE PUTTING IN THE INFO FOR A TRANSPONDER HIT THE RED KEY ON YOUR REMOTE AND YOU WILL NOW SEE IT IN THE LIST OF TRANSPONDERS.

HIT THE YELLOW KEY AGAIN TO ADD ANOTHER TRANSPONDER AND KEEP DOING THAT UNTIL YOU HAVE ALL 32 IN THE LIST.

WHEN YOU HAVE ADDED ALL THE TRANSPONDERS AND ARE IN THE TRANSPONDER LIST ON THE RIGHT JUST HIT THE OK BUTTON ON YOUR REMOTE AND YOU WILL NOW BE ON THAT TRANSPONDER IN THE ANTENNA SETUP BOX AND IT WILL BE HIGHLIGHTED.

USING YOUR LEFT OR RIGHT ARROW YOU SHOULD NOW BE ABLE TO SCROLL THROUGH ALL THE TRANSPONDERS YOU JUST ADDED.

You have now successfully added a new satellite (ANIK F3 118.8W) and added all the info it needs (transponders) in order to scan for channels.

Next set up that Satellite as you have 110W and 119W with your LNB TYPE, LNB FREQUENCY, DISEQC PORT FOR 118.8. ETC

NEXT HIT THE EXIT BUTTON ON YOUR REMOTE.

YOU WILL GET A MESSAGE "SAVING PLEASE WAIT" AND AFTER A FEW SECONDS OR SO IT WILL GO OUT AND RETURN YOU TO WHATEVER CHANNEL YOU WERE ON.

NEXT GO BACK TO

MENU>INSTALLATION>ANTENNA SETUP AND GO TO THE SATELLITE 118.8W ANIK F3 make sure that you have good strength and quality signals (GREEN BARS AND SAT 118.8W SHOWS AS LOCKED IN)

NOW SCROLL DOWN TO SAT Search START and HIT OK AND IT WILL AUTOMATICALLY SEARCH FOR CHANNELS ON 118.8W

WHEN IT IS DONE WITH THE SAVE BOX HIGHLIGHTED HIT THE OK ON YOUR REMOTE AND IT WILL GIVE YOU A MESSAGE SAVING PLEASE WAIT AND THEN RETURN YOU TO ANTENNA SETUP HIT EXIT.

FINALLY IF USING NFPS YOU SHOULD NOW HIT THE F1 BUTTON ON YOUR REMOTE FOR THE NEWCAMD CONTROL PANNEL.

HIT THE BLUE BUTTON TO STOP ALL

HIT THE GREEN BUTTON TO START THE PROTOCOL

*YOU SHOULD SEE STOP CHANGE TO CONNECTING AND THEN RUN NAGRA (0X1816)

HIT THE EXIT ON THE REMOTE AND CHANGE YOUR CHANNEL TO ONE THAT IS ON THE NFPS CHANNEL LIST FOR 118.8W ANIK F3

YOU SHOULD NOW BE WATCHING IT ON YOUR TV.


GOOD LUCK